Saturday, April 21, 2012

From Front to Back

It feels food to have gotten some of the front suspension linkages completed.  For the next part to make I'll switch from the front of the bike to the back and do some work on the swingarm.  I know Scott has had plenty of spare time lately and would like nothing more than to start forming the sheet and welding it up.

The swingarm is a welded assembly of a lot of folded sheet and billet CNC parts.

The sheet parts were cut out by North East Water Jet from 6061-T0 material because of the various forming and bending operations that need to be done.
 
T0 temper is full soft and can easily be bent without tearing or other material disruptions.  T4 or T6 temper are a lot stronger but have issues with formability.  Since T0 temper is so soft, you may ask how will it be strong enough to withstand the loads of a roadrace motorcycle.  The answer is simple: after welding, the entire assembly will be heat treated to a T6 temper.

This is as of yet an unresolved area.  I need to make a welding/heat treat fixture that is light enough to manipulate to gain welding access, strong enough to keep the parts in proper alignment, and of a material that can withstand the T6 processing temperature of aluminum without weakening.  Good candidates are cast iron surface plates or old machine tool tables or beds.  As I have neither on hand this needs to be sourced at minimal expense.  If any readers have something suitable please drop a line.  12x24 is a minimum size.

The billet parts are made from 6061-T6511 material as getting material in bar form in tempers other than T6xxx is difficult and largely unnecessary as bar material is rarely bent or formed, it is usually machined, for which a T6 temper is desirable.  T4 and especially T0 tempers tend to be gummy when machined and leave an unsatisfactory surface finish.  Some areas of the billet parts will lose their T6 temper during welding but will be restored to full strength by the subsequent heat treat process.
Scott machined the axle mount/chain tension adjuster parts and they are damn good looking.  The remaining billet parts are the linkage mount/pivot bearing support and the upper shock mount.  Today's post will be on the first machining steps of the linkage mount/pivot bearing support part.


This is a decently large part that will withstand considerable loading from chain tension, shock force, and tire traction.  The part has several features to locate and interlock the various sheet parts in proper alignment.  today's post will be some of the relatively simple bottom features: the shock clearance hole, the linkage mount pocket, and some fixturing holes and clearance operations.

I will be able to make 2 parts totaling 5.5 lbs from this 73lb block of billet material.  It may seem wasteful but is really the most efficient way to make a couple of untested parts.  The waste chips will be recycled into delicious Italian heroes.
Most woodworkers cringe when they see me machining aluminum on a table saw.  In reality it is a great way to trim stock accurately to size.  Bandsaws are nice but leave a ragged edge.  With the proper carbide tipped blade the resulting finishes are excellent.  In my infancy as a machinist I was as reluctant as anyone to cut metal on a table saw but years ago after witnessing Eric Moore cut stock for a project to size and square within +/-.005, I was a convert.  My technique is not as smooth as Eric's but it gets the job done.

For anyone that doubts that I actually cut 2.5" thick aluminum plate (in 2 passes) with the table saw....
Smooth as butter.  A little WD-40 goes a long way in saw cutting aluminum.

With these two plates I needed to machine trunnion mounting holes then will flip the part and machine the underside.
Here it is clamped to the trunnion:
And here are the 4-16mm reamed/M12-1.75 threaded holes i use to bolt parts down:
 After machining both blanks I bolt one ot the table and start machining:
The 2" ripper mill used in the TZ250 case project worked like a dream on this part.

Two blanks, two parts!

Now I need to do a bunch of CAM programming as the 'inside' of the part is much more complex than the bottom size.  Hopefully will be able to post more this week.


Chris

Tuesday, April 17, 2012

Finishing the Upper Control Arm

Good weather and motorcycle parts, almost a perfect combination.  It would be perfect if all those motorcycle parts fit together to make a complete bike you can ride around in this summer preview.  One day soon!

I was able to get more time on the project and finished up the machining of the upper control arm.  I was able to make a second use of the baseplate for the crankcase girdle as one of the needed holes intersected with any of the existing holes.  After a little bandsaw prep to cut off large excess stock areas I was ready for more machining.


Those chunks went into the recycling bucket that gets emptied every few weeks and results in a nice Lisa's Deli sandwich for everyone lucky enough to be in the shop that day.  They make great fresh mozzarella.

Now back to the mill with the part bolted onto the trunnion with a baseplate and a few precision spacers to lift the part a bit off the table surface.
The first operation results in a recognizable part and a lot of chips.
Then I turn the table and rough out the bearing bores and give the arm its tapering profile.
Now fine boring the bearing pocket to a M6 tolerance grade.  That's Peter's boring head and bar.  Its a very nice setup he got from Mari Tool.

Then I spin the baseplate and drill and counterbore the trail adjustment screw hole.
This operation is semi-manual, the tool is a 2 piece assembly: a keyed shaft and removable counterbore cutting head.  It is used a lot in the aircraft industry where it is not possible to get a spindle on the correct side of a hole to make a counterbore.  So at the price of a little manual intervention you can get a clean spotface for a screw head where you otherwise would not be able to.  It is a good technique which I've used on both V4 crankcase castings, some main case bolts on the recent billet TZ250 crankcase project, and now on this suspension link.  There are automated tools that accomplish the same thing at a greatly increased price.  When my production volumes make the manual technique unwieldy than an automatic tool will be purchased.

There are 4 screws that hold this adjustable arm design together.  To maximize clamping force over the largest possible area instead of using washers I machined some 6Al-4V Titanium cap plates.  These cute little parts prevent marring and ensure a tightly clamped joint.  Since the trunnion was still on Peter's mill I used my Bridgeport CNC knee mill to make these.  While this machine is in no way capable of making 90% of the parts in this project it is perfectly suitable for a lot of the smaller less dimensionally critical parts.  There was even a piece of aluminum already clamped in the vice that I could use as a baseplate.
I had a sheet of Ti from another project that was the perfect size.  I machined 2 holes on the manual mill, bolted the part down, than ran the program that automatically separates the part from the extra stock upon completion.
Drill new holes, repeat a few times and there are enough parts for 2 complete arms.
One more assembly to cross off the To-Do list.  Yea!


Chris